- Make
- Dragon
- Model
- 110 BBL
- Category
- Construction / Spare Parts, Components and Attachment
- Location
-
North America: United States of America
6642 Industrial RD, 77705, Beaumont, - USA - Condition
- new
- Price
- Price on Request
I-10 EQUIPMENT SALES
is selling this:
Dragon 110 BBL
Description
- **Price does not include 12% FET (Federal Excise Tax).
- 5 Axle Removable Neck Heavy Haul Trailer
- Specifications:
- Type: Low Profile Flat Bed with removable neck.
- Payload: 60 tons (120,000 lbs.) distributed over 16 ft.
- Overall length: 59’ – 8”
- Deck length: 45’ – 0”
- Deck width: 8’ – 6” (102”)
- Deck height: 3’ – 5” (41”)
- Deck Camber: 2” nominal, neck to tail
- King Pin Settings: 16” and 34”
- Swing Clearance: 8’ – 6’ (102”) and 10’ – 0” (120”)
- Frame: 4 beam design. Fabricated beams from a A514 T-1 high tensile steel flanges and webs. Main beams boxed reinforced at critical deck transition, 2-1 minimum safety factor at maximum payload stresses
- Front Deck: 22’ -8” L, 2” apitong attached at ends and every other cross member
- Rear Deck: 22’ -4” L including tail roller, 1/4” steel plate deck, continuous welds on top, intermittent welds on under side
- Neck: Mechanical removable with roller at rear, 2 King Pin locations, spare tire carrier each side • Rear Deck Roller: 8” SCH 160 pipe (8 5/8” OD) with double spherical bearings, 2 sets of over load rollers, grease fittings on main roller and overload rollers
- Neck Roller: 6” SCH 160 pipe (6-5/8” OD) with double spherical bearings, grease fittings, cable guide flanges
- Deck Load Rollers: 6” sch 160 pipe (6-5/8” OD) with double spherical bearings, grease fittings, air operated to raise, spring load to lower, used to assist in unloading skidded loads off the rear
- Pin Pockets: 1 each side at rear on 45 degree angle with 1/2” grab hooks, 2 each side in main deck inside outer beam, 7 each side on outside of outer beam
- D Rings: 15 on each side, outside of outer beam, 2 inside of neck
- Outriggers: 11 each side, forged heavy duty, locking against beam and at 90 degrees to beam
- Traction Cleats: 3/4” x 1” A514 T-1 steel, continuous welds solid on up hilltop, intermittent welds on downhill side
- Suspension: 30,000 lb (per axle) air ride, air lift on front and rear axles, manual dump all axles, travel limit straps on all axles
- Axles: 5-25,000 lb. round with outboard drums
- Wheels: 10 hole steel disc hub pilot
- Tires: 255R/70 x 22.5 Radial
- Brakes: 16 1/2 x 7, spring parking brakes on 4 axles, auto slack adjusters
- Bumper: 4” SCH 80 pipe with 4 -d rings
- Mud Flaps: Anti Sail
- Lights: Full dot lights, sealed led lights
- Coating: All surfaces near white metal steel grit blast, 2.5 ml profile (SP-6), primed and color coated (before decking) with high solids polyurethane, 4-6 ml dry film thickness.
- SerialNumber : 149447
- StockNumber : 1508
- ForSaleListPrice : 17500
*
Ø
▼